Hooking Up the Case Wiring

Once you have chose your components, the fun starts — putting it all together! Luckily building a home theater PC is not hard. If you can handle a screwdriver without stabbing yourself, you are probably going to be able to put together a PC. One precaution before you get started — touch a large metal object like your HTPC case chassis, a metal cabinet, or similar to earth yourself. Static electricity can damage some PC components. And a helpful tip — invest in a pack of cable ties in advance. Good cable management in a home theater PC build will promote air flow in the case and make your installation much easier, particularly in a small HTPC case. The starting point for our build will of course be the case.

NA

Jay, For removal of the charging port and disconnection of its cable at the plug on the motherboard, is it necessary to remove the cooling fan assembly step ? Just disconnect the left speaker as it shown in the step 16 and after that you should be able to disconnect the DC jack harness. Ian September 21, I Just had to replace the mother board in my HP G60 same as the Compaq for some reason I now can not get the new board to recognize the dvd drive.

Is there any chance that I forgot to reconnect a cable or with it being an ata drive should i just have to slide it in and be good to go?

Check to make sure the CPU fan is plugged into the 3 pin connection on your motherboard. A fan that is not spinning can lead people to believe the board is not powering on. Check to make sure your memory is aligned and installed correctly in the memory socket.

If it’s sitting idle the fan spins at the normal rate, but any activity and it sounds like it’s getting ready for takeoff. First thought was overheating. The CPU dual core temps were reading a steady low to mid 30’s C, but I went ahead and cleaned the heatsink and processor and reapplied the thermal paste. Started it up again and it’s no different, though the temperatures are reading slightly lower than before.

This is with speedfan. Most recently before I last gave up on it I checked the bios and the temps there on one of the cores was bouncing all over the place. From F to negative readings. The machine never has never shut off like I would expect from overheating, and runs normal within Windows, just with the fan revving up and down all the time.

How to connect PWM hub on Enthoo Luxe case

Where do they all go? Hooking up a computer has gotten significantly easier and more straightforward over the years; you can be connected in just a few minutes! See Step 1 below to get started. Steps 1 Place all of your equipment where you want it.

After you have installed the cooler, secure the fan power cable to one of the fan power posts on the motherboard – there should be one located near the CPU. Now you can hook up your telly and start figuring it all out – have fun! All components installed. Home Theater.

Once it allowed me to go in and change the boot order was going to try Linux as a backdoor or other live diagnostic utilities , but that was it now it just stop there, no matter if I give a little kiss or throw it across the room with all my might just kidding. You can try minimizing the system by removing parts one by one and test the laptop after each part removed.

It was lightly dropped or so the previous owner said and I believe him. Is that enough to unseat the CPU? The CPU secured pretty good. Try reconnecting memory modules, maybe one of the modules is not making good contact with the slot. Roelworks July 11, if i just want to clean the fan do i have to dissamble the whole thing…i failed with my other laptop.. It booted up like clock work and is now wonderfully silent.

Try cleaning the fan with compressed air. Blow air into the fan grill on the bottom of the laptop and after that into the grill on the side.

3 case cooling fans & 1 plug in on mobo

Finding the right CPU fan requires a great deal of research. Not only do different fan sizes populate the market, a byzantine maze of CPU socket types, bearing technologies, fan speeds and more greatly complicate the selection process. Additionally, it explains my favorite method for applying thermal compound to a CPU. The PC component that keeps your CPU cool consists of two separate parts — the heat sink, which is typically a block of metal, designed to maximize airflow and surface area.

Jul 28,  · here is the link to the manual for my motherboard. Here is the link to the manual for my case Sorry for the long explanation but i didn’t know how to simplify it haha. Reading that manual i am 99 percent sure i got everything hooked up right.

CarsonG4 2 months ago Reply Use sandpaper to rub sharp pins off the mobo motherboard and make it into a clipboard Noodleburger 6 months ago Reply The motherboard makes a good mousepad if you fully desolder, make it rectangular and put vinyl wrap on one side. WanderingAuthor 8 years ago Reply Voltage will sting, but it is the amps that will kill you. You can get a nasty burn from high voltage, but what it takes to kill you is a quarter of an amp across your heart.

A twelve volt car battery could give you a lethal jolt, if you got careless. That’s 60ma at 12V. A long time ago the U. Navy considered anything above 30V as high voltage because it was possibly lethal. This info was in an official Navy message. Just because it only zapped you and you survived does not mean it’s not deadly. It’s easier for someone to start a stopped heart than to get a fibrillating heart to beat correctly.

If you’re messing with electricity you should be smart enough to look up the correct information! You even have the internet to make it easier. I had to learn this from instructors and books. So, please quit spouting BS!

Beginners Guide: How To Install/Remove AMD Socket AM3 CPU and Heatsink

What is the function of the motherboard on the computer? A motherboard is also known as a main board, system board and logic board. A common abbreviation is ‘mobo’. They can be found in a variety of electrical devices, ranging from a TV to a computer.

Got this in the mail and was delighted to find that it came with a pigtail for hooking up both fans to a single power line. The actual cooling is fine, zero problem with the functionality. You have to remove the fans in order to attach to the motherboard – on that note, attach this before you put the motherboard in the case. The fans are.

Basically I will take the whole unit apart and remove all internal components one by one. Remove covers from the hard drive, wireless card and memory. Remove one screw securing the DVD drive red circle and pull the drive out. Remove the memory modules in my laptop I had only one module installed. Unsnap two antenna cables from the wireless card. Remove two screws securing the wireless card green circles.

Remove the wireless card. Remove five screws securing the switch board cover red circles.

Best Motherboard CPU Combo for Different Computer Types

These are the basic hardware requirements to perform a POST test. You may need a video card also if your motherboard does not have onboard video Install the processor on your motherboard.

Performance PC’s, Inc. Robert J. Conlan Blvd. NE Unit #5 Palm Bay, FL is located in beautiful Palm Bay, FL and has been in .

June 3, BTW: It was quite dense. Dust had been blowing through this slot and collecting on the chip. I sure this contributed to the overheating. The video chip is between the processor and the fan along the brass heat-sink strap. Not sure how I would cool it though. The laptop still works after this repair. NOW, for all peeps who dont know, when open you laptop for do that reflowing i talk of dvxxxx series , cut the white wire of the cpu fan.

Why not just use a heat gun.

Adding Lots Of Case Fans ?! Fan Header Y Splitter vs Hub


Hello! Do you want find a partner for sex? It is easy! Click here, registration is free!